Skip to content
Source & Brand — Global Sourcing. Brand Building.

Factory Verification & Quality Control

Pre-shipment inspection

We coordinate independent inspections of completed goods before dispatch, using your specification and agreed sampling and acceptance criteria.

What’s included

How we help with pre-shipment inspection

  • Inspection booking aligned with goods readiness
  • Quantity, appearance, dimensions and agreed function checks
  • Defect findings compared with agreed acceptance criteria
  • Report shared for your shipment or correction decision

We coordinate independent inspections of completed goods before dispatch, using your specification and agreed sampling and acceptance criteria. Source & Brand, operated via Forton General Trading LLC in the UAE, arranges qualified third-party specialists to check goods at the agreed location in China. The inspection can cover quantity, appearance, dimensions, packaging and agreed functions. Findings are documented for your review, helping you decide whether to proceed with shipment, request corrections or arrange further checks. Booking is aligned with goods readiness and the access required for the agreed inspection scope.

What a pre-shipment inspection covers

A pre-shipment inspection checks a defined consignment of completed goods against requirements agreed before the visit. It is different from a factory audit, which examines the supplier’s facilities, processes or capabilities. Here, the focus is the actual order awaiting dispatch: whether the available goods match the approved specification and whether identified defects fall within the agreed acceptance criteria. The scope should reflect the product, its intended use and the consequences of a defect.

Source & Brand coordinates the inspection rather than carrying out checks through an in-house inspection team. Qualified third-party specialists perform the agreed work and record their findings. You remain responsible for the commercial decision to release, hold or reject the consignment. An inspection provides evidence about the goods examined; it does not establish that every item in the order is defect-free or replace product-specific regulatory assessment where that is required for your destination.

Align booking with goods readiness

Booking starts with confirmation of the inspection location, supplier contact, order details and expected readiness of the goods. We coordinate with the supplier and inspection provider to establish when the agreed consignment will be available for meaningful checking. Readiness includes more than production completion: cartons must be accessible, relevant goods must be identifiable, and the supplier must allow the inspector to select samples rather than presenting only a prepared selection of products.

Before the visit, clarify whether packing must be complete and what proportion of the order needs to be available under the agreed inspection plan. Mixed orders need clear separation by product, variant or purchase order so the correct goods can be checked. If production or packing changes, tell us before the booking proceeds. Restricted access, missing stock or incomplete preparation may limit the inspection and require a revised visit or scope agreed with you.

Turn your specification into inspection instructions

Useful inspection instructions describe measurable requirements rather than broad expectations such as premium quality. Share the purchase order, product specification, approved artwork, dimensions and tolerances, materials information and any approved reference sample. Identify which document takes precedence if versions differ. For branded goods, include logo position, colour references, label content and packaging requirements. The clearer these inputs are, the easier it is to distinguish a genuine non-conformity from an unresolved interpretation of the brief.

Function checks also need an agreed method and a clear expected result. Depending on the product, these might include assembly, operation of moving parts, fit between components or a defined basic performance check. Confirm any equipment, fixtures or consumables needed at the inspection location. Where a requirement needs specialist laboratory analysis rather than an on-site check, we can coordinate separate testing with qualified third-party specialists, subject to an agreed scope and suitable samples.

  • Current specification and approved references
  • Defined tolerances and check methods
  • Packaging, labelling and artwork requirements

Agree sampling and acceptance criteria

Sampling defines how goods are selected and how many units are examined for each agreed check. The plan should suit the consignment structure and product risks, including different models, colours or sizes where relevant. If an acceptance quality limit, or AQL, approach is used, agree the applicable inspection level, defect categories and acceptance limits before the visit. These settings should not be chosen after findings are known simply to obtain a preferred inspection result.

Acceptance criteria explain how observed defects affect the inspection outcome. Critical, major and minor classifications need definitions relevant to your product, not just generic labels. A sharp edge on a handled item, an incorrect dimension affecting assembly and a cosmetic mark may require different treatment. Sampling leaves uncertainty about unexamined units, so higher-risk characteristics may need a different check method or additional assessment. The agreed plan should make these limits clear before shipment decisions.

Check quantity, condition and agreed functions

The physical inspection follows the agreed checklist and records what can be verified at the location. Quantity checks may involve carton counts, packing records and sampled contents, depending on the scope; they should not be described as a full unit count unless that work was agreed and completed. Appearance checks can cover workmanship, visible damage, finish and branding. Dimensional checks compare sampled measurements with specified tolerances using the agreed method and suitable equipment available.

Packaging checks can examine carton markings, product labels, assortment, protective materials and packing configuration against your instructions. Agreed function checks assess the selected units under the stated conditions, with any practical limitations recorded. If goods are inaccessible, required equipment is unavailable or a test cannot be completed safely, the report should identify the gap. Do not treat an omitted check as a pass or assume that a basic function check establishes durability in use.

  • Quantity and product identification
  • Appearance, dimensions and workmanship
  • Packaging and agreed function checks

Use the report to decide next steps

The inspection report is shared for your shipment or correction decision. It should identify the inspected order, sampling basis, checks performed and findings, supported by relevant photographs and measurements. Defect findings are compared with the agreed acceptance criteria, while limitations and uncompleted checks remain visible. Review both the overall outcome and the underlying evidence: a summary result alone may not explain a recurring cosmetic issue, a packaging discrepancy or a requirement outside the checklist.

Where clarification is needed, we coordinate questions with the inspection provider and supplier. You can then decide whether to authorise dispatch, hold the goods pending corrective work or request further assessment. Keep that decision separate from the supplier’s promise to resolve an issue later. If you accept a deviation, document exactly what is accepted and for which order, so it does not silently become the specification for future production or leave responsibilities unclear.

Coordinate corrections before dispatch

If findings require correction, ask the supplier for a specific action plan identifying the affected goods, proposed rework or replacement, and how corrected stock will be separated from unchecked stock. Photographs can help explain the work, but they may not demonstrate that the whole affected batch has been addressed. Where appropriate, we coordinate a reinspection with a qualified third-party specialist, using a scope that reflects the original findings and any additional risks introduced by rework.

Inspection coordination should sit alongside your dispatch arrangements, not be confused with freight release or loading supervision. Goods may ship directly from China to your destination without passing through the UAE. Confirm who can authorise shipment and how that instruction reaches the supplier or freight provider. If you need container loading checks, transport-related packaging assessment or separate laboratory testing, identify those requirements explicitly; they are not automatically included in a pre-shipment inspection booking.

Common questions about pre-shipment inspection

When should I request a pre-shipment inspection?

Request coordination while the supplier can still confirm readiness and provide the inspection documents, rather than waiting until dispatch is imminent. The visit itself is aligned with completed goods being available under the agreed plan. Allow room in your arrangements for reviewing findings and deciding whether corrections or further checks are needed.

Who performs the inspection in China?

Qualified independent third-party specialists perform the inspection. Source & Brand coordinates the scope, booking, supplier access and report sharing. We do not present the inspector as our own employee or the supplier’s factory as our facility. The inspection provider needs suitable product knowledge and the ability to perform the agreed checks.

Does a passed inspection mean every item is acceptable?

No. A sampling-based inspection examines selected units and assesses findings against agreed criteria. Unexamined goods may still contain defects, and some characteristics cannot be established through routine on-site checks. Read the sampling details, limitations and outstanding issues alongside the result before deciding whether the consignment is suitable for shipment.

Can inspection confirm compliance with destination regulations?

Routine pre-shipment inspection does not by itself establish regulatory compliance. It can check specified labels, markings or documents within the agreed scope, but some requirements need technical assessment or laboratory testing. We can coordinate qualified third-party specialists for separately agreed work. Destination requirements should be identified before deciding which checks to commission.

What happens if the inspection finds defects?

You receive the findings for review against your agreed acceptance criteria. Depending on their significance, you may request supplier corrections, replacement, further assessment or a reinspection before authorising dispatch. Source & Brand coordinates the relevant communication and follow-up scope; the commercial decision remains yours, subject to your supplier agreement.

To arrange a pre-shipment inspection, send Source & Brand your order details, specification, supplier contact, inspection location and goods readiness status. Include any approved samples, defect definitions and checks that matter most to your product. We will coordinate the proposed scope with a qualified third-party provider so you can review the inspection arrangements before proceeding.

Need pre-shipment inspection?

Tell us what you need. We’ll come back with suppliers, options and a clear next step.

Request an Inspection